Key Features
Aeration and Water Display: Combines pond aeration with an elegant, trumpet-shaped decorative water feature.
High-Volume Water Circulation: Circulates 600 gallons of water per minute.
Large Spray Pattern: Produces an approximately 12-foot-high by 18-foot-wide water pattern.
Surface Circulation: Creates a strong surface current that helps oxygenate the water and reduce algae and debris.
Oil-Free Motor: Uses an oil-free submersible motor with no oil changes required.
Low-Maintenance Design: Requires little to no routine maintenance under normal operating conditions.
Continuous Operation: Designed for 24-hour-per-day operation.
Freshwater and Saltwater Use: Designed for fresh water and approved for saltwater operation.
Winter-Ready Design: Can remain in the water with the power turned off during winter and be restarted after the water thaws.
Subzero-Condition Durability: Components are engineered to withstand subzero conditions without damage.
Optional Lighting: Compatible lighting options can be added during the initial purchase or later.
Weighted Anchoring: Supports installation using two nylon anchoring lines and two weighted anchors positioned on the pond or lake bottom.
Made in the USA: Manufactured in Holland, Michigan.
Safety Compliance: ARL-tested and compliant with UL standards and the National Electrical Code when installed as a complete package.
Specifications
Motor Rating: 1½ hp
Voltage: 230 volts
Motor Type: Oil-free, submersible motor
Motor Material: Stainless steel
Frequency: 60 Hz
Phase: Single-phase
Motor Speed: 3,450 rpm
Current Draw: 10.6 amps
Flow Rate: 600 gallons per minute
Spray Pattern: Approximately 12 feet high by 18 feet wide
Standard Power Cord Length: 100 feet
Supplied Power Cord Gauge: 12-gauge
Power Cord Type: Submersible electric power cord
Maximum Cable Length With 12-Gauge Cable: 310 feet from the motor to the main power source
Extended Cord Availability: Longer electric power cords are available.
Extension Cord Restriction: Do not use an extension cord to supply power to the motor.
Required Anchor Weight: Two 45-pound weights, concrete blocks, or similar weighted anchors
Required Anchoring Lines: Two nylon anchoring lines measuring ⅜ inch or thicker
Minimum Anchor Spacing: 25 feet apart
Anchoring-Line Position: Lines should extend outward at a 45-degree angle to the pond or lake bottom.
Operating Schedule: Designed for 24-hour-per-day operation
Alternative Electrical Configurations: Three-phase and/or 50 Hz versions are available.
GFCI Requirement: A Ground Fault Circuit Interrupter must be used.
Electrical Installation: A licensed electrical contractor must be used when supplying power to the unit.
Swimmer Safety: Always disconnect the power when swimmers are present.
Control Box Requirement: No control box required.
Propeller Maintenance: The propeller assembly should generally be replaced approximately every five years.
Anchoring-Line Maintenance: Quality nylon anchoring lines measuring ⅜ inch or thicker should generally be replaced approximately every five years.
Cleaning and Inspection: When removed for propeller or anchoring-line replacement, the unit may be cleaned with high-pressure water and visually inspected for anything restricting water flow.
Size Guide
Recommended Pond Size: Greater than ¼ acre
Minimum Pond Depth: 38 inches
Compatibility
Compatible With: Freshwater and saltwater ponds greater than ¼ acre with a minimum water depth of 38 inches.
Electrical Compatibility: 230-volt, 60 Hz, single-phase electrical service.
Application Compatibility: Suitable for commercial, residential, and municipal pond applications.
Optional Lighting: Compatible lighting options can be added during the initial purchase or later.
Included
Float platform
Pump assembly
Stainless-steel debris shield
Three self-tapping screws
100-foot, 12-gauge submersible electric power cord
Not Included
Two anchoring weights, concrete blocks, or similar weighted anchors weighing at least 45 pounds each
Two nylon anchoring lines measuring ⅜ inch or thicker
Light set Not Included
